Rabu, 30 Januari 2013

Konfigurasi BIOS



Konfigurasi BIOS
2.3.1 Setting date
Masuk CMOS Setup
Dalam utama atau sistem setup layar Anda dapat melihat tanggal dan waktu. Dengan menggunakan tombol panah, navigasi ke tanggal dan mengubah tanggal. Setelah disorot pada bulan, hari, atau tahun, Anda tekan tombol panah atau halaman atas atau bawah halaman untuk mengubah tombol tanggal.
2.3.2 Boot (booting)
Booting adalah istilah teknologi informasi dalam bahasa Inggris yang mengacu kepada proses awal menyalakan komputer dimana semua register prosesor disetting kosong, dan status mikroprosesor/prosesor disetting reset. Kemudian address 0xFFFF diload di segment code (code segment) dan instruksi yang terdapat pada alamat address 0xFFFF tersebut dieksekusi. Secara umum program BIOS (Basic Input Output System), yaitu sebuah software dasar, terpanggil. Sebab memang biasanya BIOS berada pada alamat tersebut. Kemudian BIOS akan melakukan cek terhadap semua error dalam memory, device-device yang terpasang/tersambung kepada komputer -- seperti port-port serial dan lain-lain. Inilah yang disebut dengan POST (Power-On Self Test). Setelah cek terhadap sistem tersebut selesai, maka BIOS akan mencari [Sistem Operasi], memuatnya di memori dan mengeksekusinya. Dengan melakukan perubahan dalam setup BIOS (kita dapat melakukannya dengan menekan tombol tertentu saat proses booting mulai berjalan), kita dapat menentukan agar BIOS mencari Sistem Operasi ke dalam floppy disk, hard disk, CD-ROM, USB dan lain-lain, dengan urutan yang kita inginkan.
BIOS sebenarnya tidak memuat Sistem Operasi secara lengkap. Ia hanya memuat satu bagian dari code yang ada di sektor pertama (first sector, disebut juga boot sector) pada media disk yang kita tentukan tadi. Bagian/fragmen dari code Sistem Operasi tersebut sebesar 512 byte, dan 2 byte terakhir dari fragmen code tersebut haruslah 0xAA55 (disebut juga sebagai boot signature). Jika boot signature tersebut tidak ada, maka media disk dikatakan tidak bootable, dan BIOS akan mencari Sistem Operasi pada media disk berikutnya.


Fragmen code yang harus berada pada boot sector tadi disebut sebagai boot-strap loader. BIOS akan memuat boot-strap loader tersebut ke dalam memory diawali pada alamat 0x7C00, kemudian menjalankan boot-strap loader tadi. Akhirnya sekarang kekuasaan berpindah kepada boot-strap loader untuk memuat Sistem Operasi dan melakukan setting yang diperlukan agar Sistem Operasi dapat berjalan. Rangkaian proses inilah yang dinamakan dengan booting.
2.3.3 VGA share
VGA Share memory berfungsi untuk mengatur jumlah memory yang dialokasikan untuk VGA Card Onboard yang diambil dari RAM. Biasanya mulai dr 1MB - 384MB
2.3.4 Enable atau disable onboard (I/O)
Fungsi BIOS yang digunakan untuk mengenable (aktif) atau mendisable (non aktif) pada media antarmuka (I/O) pada onboard motherboard.
2.3.5.Beep code
Beep code itu diberikan oleh komputer untuk short diagnostic pada waktu power-up, ini disebut POST, dari POST inilah kita bisa tahu kerusakan atau kekurangan apa yang terjadi
Untuk AWARD BIOS :
No Beeps No Power, Loose Card, or Short.
1 Short Beep Normal POST, computer is ok.
Short Beep POST error, review screen for error code.
Continuous Beep No Power, Loose Card, or Short.
Repeating Short Beep No Power, Loose Card, or Short.
One Long and one Short Beep Motherboard issue.
One Long and Two short Beeps Video (Mono/CGA Display Circuitry) issue.
One Long and Three Short Beeps. Video (EGA) Display Circuitry.
Three Long Beeps Keyboard / Keyboard card error.
One Beep, Blank or Incorrect Display Video Display Circuitry


B.Untuk Phoenix BIOS : 1-1-1-3 Verify Real Mode.
1-1-2-1 Get CPU type.
1-1-2-3 Initialize system hardware.
1-1-3-1 Initialize chipset registers with initial POST values.
1-1-3-2 Set in POST flag.
1-1-3-3 Initialize CPU registers.
1-1-4-1 Initialize cache to initial POST values.
1-1-4-3 Initialize I/O.
1-2-1-1 Initialize Power Management.
1-2-1-2 Load alternate registers with initial POST values.
1-2-1-3 Jump to UserPatch0.
1-2-2-1 Initialize keyboard controller.
1-2-2-3 BIOS ROM checksum.
1-2-3-1 8254 timer initialization.
1-2-3-3 8237 DMA controller initialization.
1-2-4-1 Reset Programmable Interrupt Controller.
1-3-1-1 Test DRAM refresh.
1-3-1-3 Test 8742 Keyboard Controller.
1-3-2-1 Set ES segment to register to 4 GB.
1-3-3-1 28 Autosize DRAM.
1-3-3-3 Clear 512K base RAM.
1-3-4-1 Test 512 base address lines.
1-3-4-3 Test 512K base memory.
1-4-1-3 Test CPU bus-clock frequency.
1-4-2-4 Reinitialize the chipset.
1-4-3-1 Shadow system BIOS ROM.
1-4-3-2 Reinitialize the cache.
1-4-3-3 Autosize cache.
1-4-4-1 Configure advanced chipset registers.


1-4-4-2 Load alternate registers with CMOS values.
2-1-1-1 Set Initial CPU speed.
2-1-1-3 Initialize interrupt vectors.
2-1-2-1 Initialize BIOS interrupts.
2-1-2-3 Check ROM copyright notice.
2-1-2-4 Initialize manager for PCI Options ROMs.
2-1-3-1 Check video configuration against CMOS.
2-1-3-2 Initialize PCI bus and devices.
2-1-3-3 Initialize all video adapters in system.
2-1-4-1 Shadow video BIOS ROM.
2-1-4-3 Display copyright notice.
2-2-1-1 Display CPU type and speed.
2-2-1-3 Test keyboard.
2-2-2-1 Set key click if enabled.
2-2-2-3 56 Enable keyboard.
2-2-3-1 Test for unexpected interrupts.
2-2-3-3 Display prompt "Press F2 to enter SETUP".
2-2-4-1 Test RAM between 512 and 640k.
2-3-1-1 Test expanded memory.
2-3-1-3 Test extended memory address lines.
2-3-2-3 Configure advanced cache registers.
2-3-3-1 Enable external and CPU caches.
2-3-3-3 Display external cache size.
2-3-4-1 Display shadow message.
2-3-4-3 Display non-disposable segments.
2-4-1-1 Display error messages.
2-4-1-3 Check for configuration errors.
2-4-2-1 Test real-time clock.
2-4-2-3 Check for keyboard errors


2-4-4-1 Set up hardware interrupts vectors.
2-4-4-3 Test coprocessor if present.
3-1-1-1 Disable onboard I/O ports.
3-1-1-3 Detect and install external RS232 ports.
3-1-2-1 Detect and install external parallel ports.
3-1-2-3 Re-initialize onboard I/O ports.
3-1-3-1 Initialize BIOS Data Area.
3-1-3-3 Initialize Extended BIOS Data Area.
3-1-4-1 Initialize floppy controller.
3-2-1-1 Initialize hard-disk controller.
3-2-1-2 Initialize local-bus hard-disk controller.
3-2-1-3 Jump to UserPatch2.
3-2-2-1 Disable A20 address line.
3-2-2-3 Clear huge ES segment register.
3-2-3-1 Search for option ROMs.
3-2-3-3 Shadow option ROMs.
3-2-4-1 Set up Power Management.
3-2-4-3 Enable hardware interrupts.
3-3-1-1 Set time of day.
3-3-1-3 Check key lock.
3-3-3-1 Erase F2 prompt.
3-3-3-3 Scan for F2 key stroke.
3-3-4-1 Enter SETUP.
3-3-4-3 Clear in-POST flag.
3-4-1-1 Check for errors
3-4-1-3 POST done--prepare to boot operating system.
3-4-2-1 One beep.
3-4-2-3 Check password (optional).
3-4-3-1 Clear global descriptor table.


3-4-4-1 Clear parity checkers.
3-4-4-3 Clear screen (optional).
3-4-4-4 Check virus and backup reminders.
4-1-1-1 Try to boot with INT 19.
4-2-1-1 Interrupt handler error.
4-2-1-3 Unknown interrupt error.
4-2-2-1 Pending interrupt error.
4-2-2-3 Initialize option ROM error.
4-2-3-3 Extended Block Move.
4-2-4-1 Shutdown 10 error.
4-3-1-3 Initialize the chipset.
4-3-1-4 Initialize refresh counter.
4-3-2-1 Check for Forced Flash.
4-3-2-2 Check HW status of ROM.
4-3-2-3 BIOS ROM is OK.
4-3-2-4 Do a complete RAM test.
4-3-3-1 Do OEM initialization.
4-3-3-2 Initialize interrupt controller.
4-3-3-3 Read in bootstrap code.
4-3-3-4 Initialize all vectors.
4-3-4-1 Boot the Flash program.
4-3-4-2 Initialize the boot device.
4-3-4-3 Boot code was read OK.







C.Untuk AMI BIOS :
short DRAM refresh failure
2. short Parity circuit failure
3. short Base 64K RAM failure
4. short System timer failure
5. short Process failure
6. short Keyboard controller Gate A20 error
7. short Virtual mode exception error
8. short Display memory Read/Write test failure
9. short ROM BIOS checksum failure
10. short CMOS shutdown Read/Write error
11. short Cache Memory error
12.1 long, 3 short Conventional/Extended memory failure
13.1 long, 8 short Display/Retrace test failed

Tiada ulasan:

Catat Ulasan